All our products including Rubber Gaskets are in compliance to world standrads like KTW , W270,DGVW, WRAS ETC are standardized and are only manufactured with SYNTHETIC Rubber SUCH AS EPDM, NBR, SILICON,FKM,FFKM having hardness of DIN 53505, Shore A to make them resistant to water, seawater, pond water, closed loop water up to 90°C and also against alkalines up to some extend like 50% NaOH at 50o.
For effective functioning at even high temperature range of approx. +80°C and for short-term up to +90°C, HoriakiIndia Pvt. Ltd. Rubber Metal Gaskets Water Lines, Rubber Metal Gasket DGVW etc. have the density DIN 53479, g/cm3 1.384.Based on our own test facilities Horiaki India Pvt. Ltd. manufactured rubber metal gaskets are certified resistant even against natural lighting, weather and ozone. Limited only by the natural properties of vulcanized rubber our rubber metal Gaskets are not resistant against fuel, mineral oils, acids and gases.
Chemical resistance :
- Vulcanisates of natural rubber (NR) are resistant against: water, seawater, pond water, closed loop water up to 90°C
- Partly against alkalines, 50% NaOH at 50°C
- Sufficient resistant against natural lighting, weather and ozone
- Vulcanisates of natural rubber (NR) are not resistant against:fuel, mineral oils, acids and gases
Application field : The application of NR-vulcanisates is possible where natural media have to be sealed. Temperatures higher than 90°C have to be avoided.
Function and durability : The performance and life of Horiaki gaskets depend in large measure on proper storage and fitting, factors beyond the manufactor’s control.We can, however, vouch for the excellent quality of our products.With this in mind, please also observe our installation instructions.
Rubber Metal Gaskets KTW
- The gaskets are made of elastomere butadien-rubber in different types -with inside vulcanised steel ring
- Sizes at the measurement table:
d1 = Inner diameter
d2 = Outer diameter
s = Thickness
- Vulcanised rubber gasket, crosssection in lens form, rounded edges.
- Inside vulcanised steel ring, thereforegood reception of the bolt force.
- Outer diameter of the gaskets fits to theinner bolt circuit for self centering.
- Dimension in DIN EN 1514-1(replaces DIN 2690 ) for the pressureratings PN 6 to PN 40.
- DN 15 up to DN 2000
Rubber Metal Gaskets W270
- The gaskets are made of elastomere butadien-rubber in different types -with inside vulcanised steel ring.
- Sizes at the measurement table:
- d1 = Inner diameter
- d2 = Outer diameter
- s = Thickness
- Vulcanised rubber gasket, cross section in lens form, rounded edges.
- Inside vulcanised steel ring, therefore good reception of the bolt force.
- Outer diameter of the gaskets fits to the inner bolt circuit for self centering.
- Dimension in DIN EN 1514-1 (replaces DIN 2690 ) for the pressure ratings PN 6 to PN 40.
- DN 15 TO 2000
Rubber Metal Gaskets- DGVW
- The gaskets are made of elastomere butadien-rubber in different types -with inside vulcanised steel ring.
- Sizes at the measurement table:
d1 = Inner diameter
d2 = Outer diameter
s = Thickness
Vulcanised rubber gasket, cross section in lens form, rounded edges.
- Inside vulcanised steel ring, therefore good reception of the bolt force.
- Outer diameter of the gaskets fits to the inner bolt circuit for self centering.
- Dimension in DIN EN 1514-1 (replaces DIN 2690 ) for the pressure ratings PN 6 to PN 40.
- DN 15 TO 2000
Rubber Metal Gaskets water lines
- The gaskets are made of elastomere butadien-rubber in different types -with inside vulcanised steel ring.
- Sizes at the measurement table:
d1 = Inner diameter
d2 = Outer diameter
s = Thickness
- Vulcanised rubber gasket, cross section in lens form, rounded edges.
- Inside vulcanised steel ring, therefore good reception of the bolt force.
- Outer diameter of the gaskets fits to the inner bolt circuit for self centering.
- Dimension in DIN EN 1514-1 (replaces DIN 2690 ) for the pressure ratings PN 6 to PN 40.
- DN 15 TO 2000
- Rubber-Metal-Gaskets – Safe sealing of gases and liquids
- Safe sealing of water, gas, air, acids, alkalis and hydrocarbons with low sealing forces at temperatures up to 200°C, depending on the elastomer type.
- Rubber-metal-gaskets are used where safe sealing of conventional up to special industrial media such as gases and liquids are required under usual installation conditions like temperatures, pressures and forces
- Suitable for all flange materials
- A flange connection has to be always treated as a coherent system, because the sealing functions is determined by the interaction of individual elements including flanges, gaskets and screws
HORIAKI HRS
- Rubber gasket, lenticular shape, rounded edges. Steel ring, chemically treated, no possibility to separate the elastomers from the steel core. Suitable for flanges made of metal.
- Self-centering with the same flange DN and PN appropriate tightening torques
- Self-limiting compression surface
- Rigid gasket, easy to install
- Soft surface in order to seal slightly damaged flange surfaces
- Blow-off proof n Materials :NR, NBR, EPDM, CSM, FKM
- Dimensions according to EN 1514-1 depending on DN: PN 6 to PN 40 DN 15 up to DN 2000
HORIAKI HRS/S
- Rubber gasket, Lenticular shape at the sealing body, with integrally molded spear tip at the inside diameter of the gasket, rounded edges. The spear tip provides higher safety at lowest contact pressures.. Suitable for installation between flanges made of metal and plastic
- Self-centering with the same flange DN and PN
- Minimum tightening torques and smaller than HRS (see diagram below)
- Materials of HORIAKI HRS/S : NBR, EPDM, FKM, EPDM fire resistant
- Dimensions according to EN 1514-1 depending on DN: PN 10 to PN 40 DN 15 up to DN 1000
HORIAKI HRS/TS
- Rubber gasket, flat shape at the sealing body, with integrally molded spear tip at the inside diameter of the gasket, rectangular outside diameter. The spear tip provides higher safety at lowest contact pressures.
- suitable for flanges made of plastics such as PE, PP, GRP, PVC
- Self-centering with the same flange DN and SDR
- Reduced dead space
- Tight, also at low tightening torques
- Materials of HORIAKI HRS/TS: NBR, EPDM, FKM
- Dimensions according to the valid European standards for plastic tubes made of PE, PP, PVC, PVDF and GRP (mainly SDR 11,17 and 33)
Materials of rubber-metal-gaskets
NR
- Field of application: Water ,Circuit water ,Diluted alkalis up to max. 50% and max. 80°C
- Temperature: approx. +80°C, short-term up to +90°C
- Colour: Black
- Certificates: EN 681 -1 WC Class 70
- Applications: NR vulcanized materials can be used where noncritical media have to be sealed. Higher temperatures than 90°C have to be avoided
NBR
- Field of application: Gas Media containing hydrocarbon Waste water Water
- Color: black
- Temperature: from -15°C to +100°C
- Certificates: DVGW Certificate acc. to EN 682 GBL, EN 681-1 WG Class 70, EN 682 GBL Class 70 ,TA-Luft (German Clean Air Act)
- Applications of NBR vulcanized materials result from the listed characteristics, such as resistance against aliphatic carbohydrates, mineral oils, greases fuels
Epdm
- Field of application: Drinking water, Waste water Process water
- Color: black
- Temperature: from -40°C to +110°C, short-term up to +130°C
- Certification:EN 681 -1 WAL/WCL Class 70 ,Elastomer Guideline (new KTW,) DVGW W270 ACS, WRAS (BS6920), FDA Certificate, TA-Luft (German Clean Air Act)
- Applications of EPDM vulcanized materials mainly result from the good resistance to chemicals. Furthermore, the EPDM quality has a good resistance against ozone and aging.
Csm
- Application in case of alkalis and acids in the chemical industry
- Color: black
- Temperature: from -10°C to +80°C
- Certification: TA-Luft (German Clean Air Act)
- Applications of CSM vulcanized materials can be found in the chemical industry, in chemical cleaning etc.
FKM(VITON)
- Application in case of higher temperatures (Viton is the brand name of DuPont ® for FKM) in the chemical industry
- COLOR: brown
- Temperature: from -20°C to +200°C
- Certification: TA-Luft (German Clean Air Act)
- Due to the good resistance against acids and alkalis, the main use is in the area of chemistry and their users.
HORIAKI HRS-ptfelon
- Rubber-Metal-Gasket with PTFE jacket
- Gasket material: EPDM ethylene-propylene-rubber developed in accordance with the main European drinking water requirements. Very good properties of resistance against ozon and ageing.
- Material for jacket: Virginal PTFE up to DN 900, modified PTFE from DN 1000
Dimensions:
- HRS: DN 15 up to DN 2000 acc. to EN 1514-1.
- HRS/TS: DN 16 up to DN 400 SDR 11 and 17
- Application field: Safe sealing of pipe systems where aggresive fluids are flowing. Specially suitable for coated flanges and plastic flanges in PE, PP, PVC and GRP. PTFE is quite against all fluid resistant
INTERNATIONAL MARKET
- EUROPE: GERMANY, FRANCE, ITALY, UNITED KINGDOM (UK), DENMARK, NETHERLANDS, SWEDEN, SWITZERLAND, NORWAY, CZECH REPUBLIC, LUXEMBORG, IRELAND, AUSTRIA, BELGIUM, POLAND, SPAIN, CROATIA, GREECE, POLAND, ICELAND, HUNGARY, ROMANIA
- UNITED STATES(USA), CANADA, MEXICO
- RUSSIA
- AUSTRALIA AND NEW ZEALAND
- ASIA: JAPAN, SINGAPORE, MALAYSIA, THAILAND, INDONESIA, CHINA
- Middle East AND AFRICA: Saudi Arabia, Kuwait, QATAR, Bahrain Africa: Algeria, Kenya, Tunisia, Angola, Morocco, Senegal, Egypt, Nigeria, Uganda, Libya, Liberia, Swaziland etc
Indian Market
Jammu, Kota, Jalandhar, Jabalpur, Mumbai, Hyderabad, Bareilly, Varanasi, Kolhapur, Pune, Vadodara, Kanpur, Tiruchirappalli, Salem, Nashik, Jaipur, Kolkata, Surat, Delhi, Gorakhpur, Kozhikode, Aligarh, Amravati, Ghaziabad, Bhiwandi, Jamshedpur, Bengaluru, Aurangabad, Ahmedabad, Indore, Hubli Dhanbad, Thiruvanathpuram, Guntur,Guwahati,Patna, Nagpur, Warangal, Dhanbad, Faridabad, Belgaum, Dehradun, Madurai, Amritsar, Chennai, Chandigarh,Durg Bhilai, Meerut, Ludhina, Bhubaneswar, Asansol, Solapur, Agra, Rajkot, Coimbatore, Pondicherry, Bikaner, Bhopal, Moradabad, Vijayawada, Mysore, Allahabad, Cuttack, Jamnagar, Vishapatnam, Ranchi, Srinagar, Tiruppur, Lucknow, Mangalore, Jodhpur, Kochi, Gwalior, Raipur